Cab Racks | Northern-Light CR

  • The All New Northern-Light Cab Rack unit comes standard with a 3 door enclosure and LED lights (as shown).
  • 2 chain hangers in each outside compartment and a 6’ Wiring harness.
  • 2 heavy duty shelves in the center L compartment. The enclosure is 8” deep / 9” with the door.

  • It does not have rear beams, you can mount the unit 5” closer than a normal enclosure unit.
  • The unique foot allows you to mount it with a 3240 U-bolt kit or it can mount like a Short Foot by bolting through the frame web. Stocked in most Merritt warehouse locations.

General Dimensions

General Dimensions

General Dimensions

General Dimensions

General Dimensions

General Dimensions

Attention:

  • Must be Installed to Merritt Specifications with a Merritt Mounting Kit.
  • Mounting Kits not Included.
warningNEVER haul a log trailer or a pole trailer with this cab rack installed. It is a misuse of the cab rack and is strictly prohibited by Merritt Aluminum Products Company.

This cab rack is NOT A SAFETY DEVICE and will NOT PREVENT SERIOUS INJURY or DEATH from forward shifting cargo as a result of an accident or improper securement.

To prevent SERIOUS INJURY or DEATH:

    • ALWAYS secure your cargo in compliance with FMCSA/DOT regulations. See 49 CFR 393 for specific requirements. Be aware of any applicable state motor carrier regulations.
    • NEVER consider this cab rack to be part of your cargo securement system. It is not a substitute for any cargo securement device and does not change any of the cargo securement requirements.
    • NEVER allow cargo to contact cab rack or use cab rack as a tie down point.
    • NEVER haul a log trailer or a pole trailer with this cab rack installed. It is a misuse of the cab rack and is strictly prohibited by Merritt Aluminum Products Company.
    • INSPECT cab rack weekly for cracks or damage. If damaged, replace cab rack.
    • CHECK torque of all bolts every 90 days. Bolts on Moon Brackets 150ft.-lbs. dry.
    • Use cab rack for storing chains and equipment. For more information, visit www.merrittproducts.com
    • ONLY use a Merritt Mounting Kit. If a Merritt Mounting Kit is not used to install a Merritt cab rack, then your cab rack warranty will be void.

WARNING - NEVER reuse a mounting kit.

ALWAYS read and follow the Merritt Mounting Kit Assembly Instructions to ensure proper installation. If you do not have the proper equipment or skill to install the cab rack, take your vehicle to an authorized dealer.

Models and/or Specifications Subject to Change Without Notice.

F.O.B. - Atlanta GA, Birmingham AL, Dallas TX, Henderson CO, Houston TX, Minneapolis MN, Nashville TN, Pittsburgh PA, Sacramento CA, Kansas City KS, Calgary, AB (Canada), Toronto, ON (Canada)

Feet

The foot is made of steel and is Zinc plated for anti-rust and a finished look.

Foot assembly with the cut outs

Foot assembly with the cut outs for the U-bolts to mount through and also, the pre-drilled mounting holes for side mounting. Your choice!

Inside view of the foot

Inside view of the foot. Please note the design to achieve the strength needed

Shelves

Center compartment with 2 shelves

Chain hangers

Chain hangers in each side compartment

No rear beams

No rear beams. You can get the unit closer to the cab than a normal LSR.

8-11 inch deep

8 or 11 inch deep enclosure

Order # Description Shipping Weight
3700 Northern-Light Cab Rack 68 x 84 x 8 Deep, All Diamond Plate 302 Lbs.
3701 Northern-Light Cab Rack 68 x 84 x 8 Deep, Bright Smooth Doors 302 Lbs.
3702 Northern-Light Cab Rack 68 x 84 x 8 Deep, Stainless Steel Doors 302 Lbs.
3710 Northern-Light Cab Rack 68 x 84 x 11 Deep, All Diamond Plate 302 Lbs.
3711 Northern-Light Cab Rack 68 x 84 x 11 Deep, Bright Smooth Doors 302 Lbs.
3712 Northern-Light Cab Rack 68 x 84 x 11 Deep, Stainless Steel Doors 302 Lbs.
3240 Northern-Light Clamp Kit (14" U-bolts) 31 Lbs.